KELLY-MOORE PAINT CO INC -- 1240-SERIES (ALL COLORS), ACRY-SHIELD (SUPDAT) -- 8010-00N077083 
=====================  Product Identification  =====================

Product ID:1240-SERIES (ALL COLORS), ACRY-SHIELD (SUPDAT)
MSDS Date:09/21/1994
FSC:8010
NIIN:00N077083
=== Responsible Party ===
Company Name:KELLY-MOORE PAINT CO INC
Address:1015 COMMERCIAL ST
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Info Phone Num:415-592-8337
Emergency Phone Num:800-424-9300 (CHEMTREC)
CAGE:0Y837
=== Contractor Identification ===
Company Name:KELLY-MOORE PAINT CO INC
Address:987 COMMERCIAL ST
Box:City:SAN CARLOS
State:CA
ZIP:94070
Country:US
Phone:650-592-8337
CAGE:0Y837

=============  Composition/Information on Ingredients  =============

Ingred Name:ETHYLENE GLYCOL (SARA 313) (CERCLA)   VP: 0.1 @ 68F
CAS:107-21-1
RTECS #:KW2975000
Fraction by Wt: 2-4%
OSHA PEL:N/K 
ACGIH TLV:50 PPM, VAPOR, C
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB

Ingred Name:SILICA, CRYSTALLINE - CRISTOBALITE; (SILICA, CRYSTALLINE) 
    (MFR'S CAS # 14464-45-1)
CAS:14464-46-1
RTECS #:VV7325000
Fraction by Wt: 2-5%
OSHA PEL:N/K 
ACGIH TLV:0.05 MG/M3 RDUST

Ingred Name:PROPIONIC ACID, 2-METHYL-, MONOESTER WITH
    2,2,4-TRIMETHYL-1,3-PENTANEDIOL; (TEXANOL)	 VP: 0.04 @ 68F
CAS:25265-77-4
RTECS #:UF6000000
Fraction by Wt: 1-2%
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:ZINC OXIDE (SARA 313) (CERCLA)
CAS:1314-13-2
RTECS #:ZH4810000
Fraction by Wt: 0-2%
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Ingred Name:PIGMENTS (SUCH AS INGREDIENTS 6-8)
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:MINERAL SILICATES
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:SILICON DIOXIDE
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:TITANIUM OXIDE; (TITANIUM DIOXIDE)
CAS:13463-67-7
RTECS #:XR2275000
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Ingred Name:PAINT PRESERVATIVES CONTAINING INGREDIENTS 10, 11 AND/OR 12
RTECS #:9999999ZZ
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:4-ISOTHIAZOLIN-3-ONE,5-CHLORO-2-METHYL-
CAS:26172-55-4
RTECS #:NX8156850
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:CARBAMIC ACID, BUTYL-,3-IODO-2-PROPYNYL ESTER
CAS:55406-53-6
RTECS #:EZ0950000
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:ANTIMICROBIAL PRESERVATIVE
CAS:26530-20-1
OSHA PEL:N/K 
ACGIH TLV:N/K 

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:YES    IARC:YES	  OSHA:NO
Health Hazards Acute and Chronic:ACUTE: DIZZINESS, HEADACHE, NAUSEA,
    CONFUSION, IRRITATION TO UPPER RESPIRATORY TRACT, SKIN AND EYE
    IRRITATION. CHRONIC: PROLONGED AND/OR REPEATED OVEREXPOSURE TO HIGH
    CONCENTRATIONS OF RESPIRABLE (AIR BORNE) CRYSTALLINE SILICA DUSTS
    AS MAY BE GENERATED BY SANDING OR GRINDING OF DRIED PAINTS AND
    OTHER (EFTS OF OVEREXP)
Explanation of Carcinogenicity:SILICA, CRYSTALLINE-CRISTOBALITE: IARC
    MONOGRAPHS, SUPPLEMENT, VOL 7, PG 341, 1987:GROUP 2A. NTP 7TH
    ANNUAL (SUPDAT)
Effects of Overexposure:HLTH HAZ: BUILDING MATERIALS WITHOUT WEARING
    PROPER RESPIRATORY PROTECTION CAN CAUSE SILICOSIS, A NON-CANCEROUS
    LUNG DISEASE THAT CAN RESULT IN SUBSTANTIAL IMPAIRMENT OF BREATHING
    FUNCTION.
Medical Cond Aggravated by Exposure:NONE KNOWN. SEE YOUR MD FOR
    SPECIFIC MEDICAL OPINION REGARDING YOUR CONDITION.

=======================  First Aid Measures  =======================

First Aid:INHALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. CONSULT
    MD. EYES: FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15
    MINUTES. GET MEDICAL ATTENTION. SKIN: WIPE OFF WITH A RAG. WASH
    THOROUGHLY WITH  SOAP AND WATER. INGESTION: CONSULT HOSPITAL
    EMERGENCY ROOM OR POISON CONTROL CENTER IMMEDIATELY.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:USE NIOSH APPROVED SCBA AND FULL PROTECTIVE
    EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE (DUE TO THE
    BUILDUP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:VENTILATE AREA TO PREVENT BUILDUP OF VAPORS.
    FOR SMALL SPILLS, SOAK UP WITH ABSORBENT. FOR LARGER SPILLS, DIKE
    AREA WITH ABSORBENT MATERIAL AND SCOOP UP LIQUIDS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE UPRIGHT IN SEALED CONTAINERS
    AWAY FROM HEAT AND FLAME.
Other Precautions:REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE A NIOSH APPRVD PARTICULATE MASK (TC-21C) TO
    AVOID BRTHG SPRAY MIST OR SANDING DUST IF LOCAL VENT IS ADEQ TO
    KEEP VAP CONCS W/IN ACCEPTABLE (TLV) LIMITS. IF LOCAL VENT IS NOT
    SUFFICIENT OR WHERE EX POSURE LIMITS ARE EXCEEDED, (SUPDAT)
Ventilation:LOCAL CROSS-VENTILATION OR MECHANICAL EXHAUST SUFFICIENT TO
    KEEP ALL HAZARDOUS VAPOR CONCS BELOW PRESCRIBED LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR'S TRADE NAME/PART NO: ACRYLIC FLAT FINISH. EXPLAN OF CARCIN: REPORT
    ON CARCINOGENS, 1994:ANTICIPATED TO BE CARCINOGEN. RESP PROT: WEAR
    A SUITABLE, PROPERLY FITTED NIOSH APPRVD RESP (TC-23C OR BETT ER)
    FOR ORGANIC VAPORS W/DUST FILTER ASNEEDED.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGS
Vapor Density:LTR/AIR
Spec Gravity:1.32-1.44
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:55-60

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NOT APPLICABLE.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
    HEATED TO DECOMPOSITION AS IN WELDING.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISCARD IN LAND FILL IN SEALED METAL CONTAINERS
    AWAY FROM HEAT AND FLAME AND IN ACCORDANCE WITH FEDERAL, STATE AND
    LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.